1 ?2012 littelfuse, inc. specifcations are subject to change without notice. please refer to www.littelfuse.com for current information. tvs diode arrays (spa ? family of products) revision: august 13, 2012 SP0504S series SP0504S low capacitance esd protection - SP0504S series description applications the SP0504S has ultra low capacitance rail-to-rail diodes with an additional zener diode fabricated in a proprietary silicon avalanche technology to protect each i/o pin providing a high level of protection for electronic equipment that may experience destructive electrostatic discharges (esd). these robust diodes can safely absorb repetitive esd strikes at the maximum level (level 4) specifed in the iec 61000-4-2 international standard without performance degradation. their very low loading capacitance also makes them ideal for protecting high speed signal pins such as hdmi, dvi, usb2.0, and ieee 1394. features ? low capacit ance of 0.85 pf (typ) per i/o ? esd protection of 12kv contact disc harge, 15kv air discharge, (iec61000-4-2) ? eft protection, iec6100 0-4-4, 40a (5/50ns) ? low leakage cur rent of 0.5a (max) at 5v ? small packaging options saves board space ? lightning protection, iec610 00-4-5, 4.5a (8/20s) ? computer peripherals ? mobile phones ? pdas ? digital cameras ? network hardware/ports ? test equipment ? medical equipment functional block diagram i/o2 i/o1 gnd i/o3 v cc i/o4 pinout i/o 1 i/o 2 sot23-6 v cc i/o 3 i/o 4 gn d life support note: not intended for use in life support or life saving applications the products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. rohs pb green application example rj-45 connecto r ethernet ph y j1 j8 gnd nc tx - rx + rx- tx + SP0504S a single 4 channel SP0504S device can be used to protect four of the data lines in a hdmi/dvi interface. two (2) SP0504S devices provide protection for the main data lines. low voltage asic hdmi/dvi drivers can also be protected with the SP0504S, the +v cc pins on the SP0504S can be substituted with a suitable bypass capacitor or in some backdrive applications the +v cc of the SP0504S can be foated or nc. SP0504S series 0.85pf diode array
?2012 littelfuse, inc. specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 2 tvs diode arrays (spa ? family of products) revision: august 13, 2012 SP0504S series low capacitance esd protection - SP0504S series caution: stresses above those listed in absolute maximum ratings may cause permanent damage to the device. this is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specifcation is not implied. absolute maximum ratings symbol parameter value units i pp peak current (t p =8/20s) 4.5 a t op operating temperature -40 to 85 c t stor storage temperature -50 to 150 c thermal information parameter rating units storage temperature range -65 to 150 c maximum junction temperature 150 c maximum lead temperature (soldering 20-40s) 260 c electrical characteristics (t op =25oc) parameter symbol test conditions min typ max units reverse standoff voltage v rwm i r 1a 6.0 v reverse leakage current i leak v r =5v 0.5 a clamp voltage 1 v c i pp =1a, t p =8/20s, fwd 9.5 11. 0 v i pp =2a, t p =8/20s, fwd 10.6 13.0 v esd withstand voltage 1 v esd iec61000-4-2 (contact) 12 kv iec61000-4-2 (air) 15 kv diode capacitance 1 c i/o-gnd reverse bias=0v 0.95 1. 1 1.25 pf reverse bias=1.65v 0.7 0.85 1. 0 pf diode capacitance 1 c i/o-i/o reverse bias=0v 0.5 pf note: 1. parameter is guaranteed by design and/or device characterization. capacitance vs. bias voltage insertion loss (s21) i/o to gnd -20 -15 -10 -5 0 1.e+06 1.e+07 1.e+08 1.e+09 1.e+10 fr equency [hz] insertion loss [db] 0.0 0.5 1. 01 .5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1.50 1.40 1.30 1.20 1. 10 1. 00 0.90 0.80 0.70 0.60 0.50 i/o capacitance (pf) i/o dc bias (v) v cc = 5v v cc = 3.3v v cc = float
3 ?2012 littelfuse, inc. specifcations are subject to change without notice. please refer to www.littelfuse.com for current information. tvs diode arrays (spa ? family of products) revision: august 13, 2012 SP0504S series SP0504S low capacitance esd protection - SP0504S series capacitance vs. frequency 0 2e-13 4e-13 6e-13 8e-13 1e-12 1.2e-12 1.4e-12 1.6e-12 1.8e-12 2e-12 1.e+06 1.e+07 1.e+08 1.e+09 fr equency [hz] capacitance [f] ti me temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p rehea t ramp-up r amp-up ramp-down r amp-d o critical zone t l to t p c ritical zon e t l to t p refow condition pb C free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 180 secs average ramp up rate (liquidus) temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max refow - temperature (t l ) (liquidus) 217c - temperature (t l ) 60 C 150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 260c soldering parameters product characteristics lead plating matte tin lead material copper alloy lead coplanarity 0.0004 inches (0.102mm) substitute material silicon body material molded epoxy flammability ul 94 v-0 notes : 1. all dimensions are in millimeters 2. dimensions include solder plating. 3. dimensions are exclusive of mold fash & metal burr. 4. blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. package surface matte fnish vdi 11-13. ordering information part number package marking min. order qty. SP0504Shtg sot23-6 e *4 3000 part numbering system part marking system sp 0504s t g series package h = sot23-6 t= tape & reel g= green silicon protection array (spa tm ) family of tvs diode arrays h e*4 e * 4 product series e = SP0504S series assembl y site (varies) number of channels
?2012 littelfuse, inc. specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 4 tvs diode arrays (spa ? family of products) revision: august 13, 2012 SP0504S series low capacitance esd protection - SP0504S series package dimensions sot23-6 o p r m recommended solder pad layout package sot23 pins 6 jedec mo-178ab millimeters inches notes min max min max a 0.900 1.450 0.035 0.057 - a1 0.000 0.150 0.000 0.006 - a2 0.900 1.300 0.035 0.051 - b 0.350 0.500 0.0138 0.0196 - c 0.080 0.220 0.0031 0.009 - d 2.800 3.000 0.11 0.118 3 e 2.600 3.000 0.102 0.118 - e1 1.500 1.750 0.06 0.069 3 e 0.95 ref 0.0374 ref - e1 1.9 ref 0.0748 ref - l 0.30 0.600 0.012 0.023 4,5 n 6 6 6 a 0o 8o 0o 8o - m 2.590 0.102 - o 0.690 .027 typ - p 0.990 .039 typ - notes: 1. dimensioning and tolerancing per a sme y14.5m-1994. 2. package conf orms to eiaj sc-74 (1992). 3. dimensions d and e1 are exclusiv e of mold fash, protrusions, or gate burrs. 4. foot length l measured at reference to seating plane. 5. l is the length of fat f oot surface for soldering to substrate. 6. n is the number of terminal positions. 7. controlling dimension: millimeter. conv erted inch dimensions are not necessarily exact. embossed carrier tape & reel speci f cation sot23-6 8mm tape and reel general information 1. 30 00 pieces per reel. 2. order in multiples of full reels onl y. 3. meets eia-481 revision "a" specifications. 2.0mm 4.0mm c l 1.75mm 1.5mm dia. hole 8mm 4.0mm 8.4mm 180mm 14.4mm 13mm 60mm access hole cover tape user direction of feed pin 1 sot-23 (8mm pocket pitch)
|
